A load of copper-nickel ore, fresh up from 3,000 feet down, recently sees its first daylight for just a few minutes before it is transferred into the enclosed loading facility at the Eagle Mine near Marquette, Michigan.
A load of copper-nickel ore, fresh up from 3,000 feet down, recently sees its first daylight for just a few minutes before it is transferred into the enclosed loading facility at the Eagle Mine near Marquette, Michigan.
I recently visited the Eagle Underground Copper-Nickel Mine and the Humboldt Processing Mill. Both are located near Marquette, in Michigan’s Upper Peninsula. Talon Metals coordinated the visit with the Lundin Mining Company which operates the Eagle Mine and Humboldt Mill Facility.
As part of my job as a legislator, I serve as a member of the House Environmental and Natural Resources Committee, the Legislative Permanent School Fund Commission and on the Iron Range Rehabilitation & Resources Board. Over the past eight years, I have visited just about every operating iron mine and taconite plant in Minnesota.
Visiting the Eagle Mine and Humboldt Plant was a real eye opener which allowed firsthand observation of the extensive environmental procedures that apply to handling the ore produced by this modern non-ferrous mine. I was struck by how very small the surface footprint of the Eagle Mine and the relative quietness at both the Eagle Mine and the Humboldt Mill.
The Eagle Mine initially recovered copper-nickel ore found at about 1,000 feet. With the discovery of the Eagle East deposit at about 3,000 feet, the life of the mine was recently extended. The copper-nickel ore is initially broken up underground and then brought to the surface in specially designed haul trucks.
It takes about two hours for a truck to make the several mile round trip from the surface down to the 3,000-foot level and back up with a load of ore. The trucks are only seen briefly on the surface for a couple of minutes when they emerge from the tunnel portal and travel a few hundred yards to deposit the ore into a completely enclosed loading facility. Those few minutes are the only time you will actually see the copper-nickel ore or concentrate out in the open. The rest of the time the ore is either in a building, a covered semi-truck or in the case of the concentrate in a covered rail car.
After the ore is deposited into the enclosed loading facility, it’s transferred to semi-trucks for the 66-mile trip to the Humboldt Mill for processing. Before leaving the mine, the covered semi-trucks must pass through a wash station to ensure that no ore residue is inadvertently tracked off the facility by the trucks.
At the mill, the ore is reduced to a fine powder. Water is added to create a slurry which allows the nickel and copper to be separated through a floatation process. The copper-nickel is skimmed off the top and further separated into nickel and copper concentrates.
Those concentrates are dried and leave the mill in covered rail cars bound for Canada for further processing. The U.S. currently does not have the ability to domestically refine high-grade nickel. Today we must import finished high-grade nickel from other countries located offshore.
All water is carefully managed at the mine and mill site. Both facilities have state-of-the-art water treatment systems. Water is not allowed to leave either site unless it meets all current environmental standards.
It’s about a six-hour trip over to the mine site, but the tour put to rest a lot of wildly inaccurate speculation of what a modern high-grade underground copper-nickel mine and processing site looks like.
Unfortunately, it’s that time of year again. Regrettably, due to State Campaign Finance rules, legislators are not allowed to send weekly legislative updates directly to you using our official state email account until after the November election.
I will continue to keep you posted via periodic news releases sent to our local newspapers. The news releases will also be available on my legislative website: www.house.mn/10b. I will continue to provide important legislative and community related information as it occurs.
I continue to work for the wonderful folks in our district every day. Despite the temporary absence of my weekly email updates, I am still taking care of business on your behalf.
The best way to contact me is via email at rep.dale.lueck@house.mn. It’s an honor to continue to serve the citizens of our district.
Until November, please be safe and enjoy the rest of the summer.
Dale Lueck (R) is the state representative for District 10B.
Your comment has been submitted.
There was a problem reporting this.
Keep it Clean. Please avoid obscene, vulgar, lewd, racist or sexually-oriented language. PLEASE TURN OFF YOUR CAPS LOCK. Don't Threaten. Threats of harming another person will not be tolerated. Be Truthful. Don't knowingly lie about anyone or anything. Be Nice. No racism, sexism or any sort of -ism that is degrading to another person. Be Proactive. Use the 'Report' link on each comment to let us know of abusive posts. Share with Us. We'd love to hear eyewitness accounts, the history behind an article.
Success! An email has been sent to with a link to confirm list signup.
Error! There was an error processing your request.
Have the latest local news delivered to your email every morning so you don't miss out on updates.
Have the latest local news delivered to your email every morning so you don't miss out on updates.
Your account has been registered, and you are now logged in.
Check your email for details.
Invalid password or account does not exist
Submitting this form below will send a message to your email with a link to change your password.
An email message containing instructions on how to reset your password has been sent to the e-mail address listed on your account.
Your purchase was successful, and you are now logged in.
A receipt was sent to your email.