So, you just got a nice big PCB back from the fab shop. You set one on your desk to admire, only to discover that it's warped. What do you do?

There are two primary types of causes of board warping: process related at the fab or assembly shop, and layout related issues.

If it's warped before assembly, it's between fab and layout. If it's flat before assembly and warped after, it's most likely between layout and assembly. That said, sometimes a fab problem won't show up until a pass through the reflow oven at your assembly partner.

Determining the root cause is generally a bit of an iterative process. It's tempting to start right off with your fab or assembly partner, but you need some information before giving them a call. You'll need such things as the amount of warpage per inch, board size and thickness. With that, you need to take a good look at your design and consider copper pours, component size and component placement.

With that information in hand, you can make your phone call. If the board is warped before assembly, call your fab shop. If it's flat pre-assembly and warped post assembly, call your assembly house.

The shop you call will want to talk over your design to help you pinpoint the cause. If you can rule out a design issue, then you need to talk with your partner to determine whether it's a fab or assembly issue, and the next steps to take care of you.

Here are a few design issues that could contribute to warping:

There may be other, more obscure causes, but those are the main design related causes. If it's none of those, talk with your partner. Occasionally, design requirements lead to a board that is essentially non-manufacturable. Hopefully, you never have this situation, but if you do, make sure that thickness, component location, pours, or cut outs really need to be the way they are.

If you absolutely, positively can't change anything, go back and try again. Then you can to look for heroic means to get the board fabricated and built. Slight warpage might go away when the board is mounted. Just be careful. Some components may not stay securely soldered when you flatten it.

The board may need a special fixture during assembly to prevent warping. This will likely cost extra, but if you can't change your design, and still need it built, it may be your best option.

Finally, if nothing works, you may need to look harder at the design, or look for a new fab or assembly house. We all like to think we can do just about anything, but every shop has its limits, and on rare occasion, those limits can be difficult to spot.

So, you just got a nice big PCB back from the fab shop. You set one on your desk to admire, only to discover that it's warped. What do you do?

There are two primary types of causes of board warping: process related at the fab or assembly shop, and layout related issues.

If it's warped before assembly, it's between fab and layout. If it's flat before assembly and warped after, it's most likely between layout and assembly. That said, sometimes a fab problem won't show up until a pass through the reflow oven at your assembly partner.

Determining the root cause is generally a bit of an iterative process. It's tempting to start right off with your fab or assembly partner, but you need some information before giving them a call. You'll need such things as the amount of warpage per inch, board size and thickness. With that, you need to take a good look at your design and consider copper pours, component size and component placement.

With that information in hand, you can make your phone call. If the board is warped before assembly, call your fab shop. If it's flat pre-assembly and warped post assembly, call your assembly house.

The shop you call will want to talk over your design to help you pinpoint the cause. If you can rule out a design issue, then you need to talk with your partner to determine whether it's a fab or assembly issue, and the next steps to take care of you.

Here are a few design issues that could contribute to warping:

There may be other, more obscure causes, but those are the main design related causes. If it's none of those, talk with your partner. Occasionally, design requirements lead to a board that is essentially non-manufacturable. Hopefully, you never have this situation, but if you do, make sure that thickness, component location, pours, or cut outs really need to be the way they are.

If you absolutely, positively can't change anything, go back and try again. Then you can to look for heroic means to get the board fabricated and built. Slight warpage might go away when the board is mounted. Just be careful. Some components may not stay securely soldered when you flatten it.

The board may need a special fixture during assembly to prevent warping. This will likely cost extra, but if you can't change your design, and still need it built, it may be your best option.

Finally, if nothing works, you may need to look harder at the design, or look for a new fab or assembly house. We all like to think we can do just about anything, but every shop has its limits, and on rare occasion, those limits can be difficult to spot.

White Paper: With the move from low-mix to high mix-manufacturing, the need for optimizing throughput across multiple batches of different product is critical to maximizing manufacturing output. Overall line utilization... View White Paper